How Much Gravel for a Driveway Base?
Updated 2026-10-27 · Yardly
Background and Pain Points
If you have ever stood in the driveway watching a delivery truck dump what looked like a mountain of stone — or worse, watched the pile run out with half the driveway still bare — you already know the pain point. Gravel is sold by volume (cubic yards) or weight (tons), but most people estimate it by eyeballing a depth. Those two things do not line up, and that gap is where budgets blow up.
The question “how much gravel for a driveway base?” has a real answer, and it is not a single number. It depends on three variables that most online calculators quietly ignore:
- The finished, compacted depth you actually need, which changes with your subsoil.
- The compaction factor — crushed stone base loses roughly 20–25% of its loose volume once it is vibrated down.
- The material you are buying — ¾-inch minus crusher run compacts very differently from clean, open-graded #57 stone.
Get any one of those wrong and you either make a second trip to the quarry (paying a second delivery fee) or end up with a 10-yard pile of leftovers in your side yard. This guide walks through the math the way a grading contractor does it, so you can order once and order correctly.
Why It Matters (Core Value)
The base course is the part of the driveway you never see again, and it does most of the work. A properly built base spreads the load of a vehicle across the subgrade so the soil underneath never gets a concentrated squeeze. Get it thin or poorly compacted and you get the classic failure pattern: wheel-track ruts, “pumping” (fine soil migrating up through the stone), edge cracking, and potholes that come back every spring.
The numbers are unforgiving. On a 12 × 40-foot driveway (480 square feet), every single inch of compacted base depth equals about 1.5 cubic yards of stone. Being one inch shy across that area is roughly a ton and a half of material you did not buy — and it is the inch that matters most, because the top of the base is where the load lives.
There is also a cost side. Over-ordering by 20% on a typical project is easy to do and hard to undo; leftover base stone is heavy, ugly, and awkward to get rid of. Under-ordering costs you a delivery minimum. Precision here is worth real money.
How to Do It Right (Step-by-Step)
Step 1: Measure the actual footprint
Measure length and width in feet, and multiply for square footage. Add a small allowance for flare-outs or a widened apron. Do not include areas that will stay lawn.
Step 2: Match base depth to your subsoil
This is the step that separates a driveway that lasts 20 years from one that lasts three. Dig a test hole 12 inches deep and feel the soil. Then use this as a starting point for compacted base depth:
| Subsoil condition | Passenger cars / light use | Occasional heavy truck or RV |
|---|---|---|
| Crushed rock, gravelly, well drained | 4 in | 6 in |
| Sandy loam, drains freely | 6 in | 8 in |
| Silt or loam, moderate drainage | 6 in | 8–10 in |
| Clay, poorly drained | 8 in + geotextile | 10–12 in |
| Expansive clay, muck, or organic soil | 10–12 in + geotextile and geogrid, or excavate and replace | 12 in+ |
Two rules sit on top of the table. First, strip all topsoil and organic material before you start counting depth — organics will rot and settle. Second, this depth covers the base only. If you plan a 1–2 inch decorative wearing surface of #57 stone or pea gravel, add that on top and excavate for the total.
Step 3: Calculate compacted volume
Multiply square footage by depth in feet.
480 sq ft × 0.5 ft (6 in) = 240 cubic feet of compacted base 240 ÷ 27 = 8.9 cubic yards, compacted
Step 4: Apply the compaction factor
Crushed stone base with fines (¾-inch minus, crusher run) typically shrinks 20–25% in volume when compacted in 4-inch lifts. So the loose volume you need delivered is compacted volume × 1.20 to 1